DEN-ON™ RD-500 Series III
Technical Specifications

858-536-5050
sales@focalspot.com

RD-500
Series III

Semi Automated BGA/SMT Rework Stations for Eutectic and Lead Free Solders

The RD Series use a high-performance 3-point heating system and advanced computer control technology, designed for safe lead free and eutectic rework applications.

DEN-ON RD-500 Specifications
Semi-Automated BGA/SMT Rework Station

DENON RD-500 Specifications	American Standard	Metric Standard
Maximum PCB Size	20 X 24"	500 X 600mm
Maximum Device Size	2.5"	60mm
Placement Accuracy	+/-.0009"	+/-0.025mm
Zoom Lens Magnification (15" monitor)	126X	126X
Top Heater Wattage (Hot Air/Gas)	700 Watts	700 Watts
Bottom Localized Heater Wattage (Hot Air/Gas)	700 Watts	700 Watts
Area Array Heater Wattage - Dark IR	2400 Watts	2400 Watts
Temperature Setting Range (Top Heater)	0 - 1202° F	0 - 650 ° C
Temperature Setting Range (Bottom Heater)	0 - 1202° F	0 - 650 ° C
Temperature Setting Range (Area Array Heaters)	0 - 1202° F	0 - 650 ° C
Air Requirements - Dry / Clean Air (4 SCFM Intermittent, Estimate at 50% duty)	44.99 PSIG	0.1 - 1.0 MPA
Nitrogen Requirements - Dry / Clean Nitrogen (Requires 1.5 SCFM intermittent)	44.99 PSIG	0.1 - 1.O MPA
Electrical Power Requirements 200-230 VAC to Ground / Neutral	200- 230 VAC	200- 230 VAC
Three (3) Wire Power Cable (Black/Black/Green) Supplied with six (6') cable	Neutral / Ground / Hot 50 / 60 HZ, 1 Phase	Neutral / Ground / Hot 50 / 60 HZ, 1 Phase
Required Circuit Amperage - Dedicated Line (Fused Neutral 15 AMP / Hot 15 AMP)	20 AMPS	20 AMPS
Plug Requirements Type	NEMA L6-30-R/30A/250V	NEMA L6-30-R/30A/250V
Receptacle Requirements Type	NEMA L6-30-R/30A/250V	NEMA L6-30-R/30A/250V
Receptacles Total (3)	1-NEMA, 2-STD/120V	1-NEMA, 2-120V Local Plug Type
Machine Weight	~ 150 Lbs	~ 78 Kgs
Maximum Load Capacity (Bench Requirements)	~ 200 Lbs	~ 90 Kgs
Physical Dimensions	W30 X D29 X H34"	W770 X D755 X H 864 mm
Working Space Requirements
FRONT Side of Machine	3'	838.2 mm
LEFT Side of Machine	1'	304.8 mm
RIGHT Side of Machine	1'	304.8 mm
REAR Side of Machine ( Service Access)	1'	304.8 mm
Machine Installation Suggested Location	Well Lighted and Well Ventilated	Well Lighted and Well Ventilated
Air Inlet Size and Fitting Type (Located in Machine Rear /Single Filter Regulation)	0.25" OD Legris Type	6.35mm OD Legris Type
Air Inlet Tubing Size (Located in Machine Rear /Single Filter Regulation)	*0.236” OD	*6mm OD
Exhaust Requirements Ventilation Flow (25CFM )	0.25" CFM	6.4 mm
Machine Height Adjustment Range (Foot Pads are 1" in Diameter)	1"	25 mm
Serial Number Location	Machine Rear	Machine Rear
Computer System
Control System	Internal Flash Contoller	Internal Flash Contoller
Power Requirements PC Controller	120 VAC	120 VAC
Video Display	15" Flat Panel Display	381 MM Flat Panel
Power Requirements Video Display	120 VAC	120 VAC

*The RD500Series uses a metric based SMC Regulator fitting for connection to factory Air. The Rework station is supplied with 6mm OD (.236”) x 4mm (.157”) black nylon tubing. The supplied 6mmOD Nylon tubing will fit in a .25” compression fitting.

RD-500 Series III Manual (Printable PDF)

The end user can be assured, that DEN-ON Instruments of Japan complies with all requirements and guideline laws on safety and efficacy, in accordance with TUV requirements and all applied standards.

The end user can be assured, that DEN-ON Instruments of Japan complies with all requirements and guideline laws on safety and efficacy, in accordance with CE requirements and all applied standards.

SITE SEARCH

WebMaster

Site Map

DEN-ON™ RD-500 Series III Technical Specifications

Semi Automated BGA/SMT Rework Stations for Eutectic and Lead Free Solders

DEN-ON RD-500 Specifications Semi-Automated BGA/SMT Rework Station

DEN-ON™ RD-500 Series III
Technical Specifications

DEN-ON RD-500 Specifications
Semi-Automated BGA/SMT Rework Station