DEN-ON™ RD-500SH Series III
Rework Stations
Technical Specifications

858-536-5050
sales@focalspot.com

RD-500SH
Series III

Semi Automated BGA/SMT Rework Stations for Eutectic and Lead Free Solders

The RD Series use a high-performance 3-point heating system and advanced computer control technology, designed for safe lead free and eutectic rework applications.

DEN-ON RD-500SH Specifications
Semi-Automated BGA/SMT Rework Station

DEN-ON RD-500SH Dimensions Front - image

DENON RD-500SH Specifications	American Standard	Metric Standard
Maximum PCB Size	16 x 18"	400 X 457mm
Maximum Device Size	2.5"	60mm
Placement Accuracy	+/-.0009"	+/-0.02 mm
Zoom Lens Magnification (15" monitor)	126X	126X
Top Heater Wattage (Hot Air/Gas)	700 Watts	700 Watts
Bottom Localized Heater Wattage (Hot Air/Gas)	700 Watts	700 Watts
Area Array Heater Wattage - Dark IR	1200 Watts	1200 Watts
Temperature Setting Range (Top Heater)	0 - 1202° F	0 - 650 ° C
Temperature Setting Range (Bottom Heater)	0 - 1202° F	0 - 650 ° C
Temperature Setting Range (Area Array Heaters)	0 - 1202° F	0 - 650 ° C
Heater Control Type	PID	PID
Air Requirements - Dry / Clean Air (4 SCFM Intermittent, Estimate at 50% duty)	44.99 PSIG	0.1 - 1.0 MPA
Nitrogen Requirements - Dry / Clean Nitrogen (Requires 1.5 SCFM intermittent)	44.99 PSIG	0.1 - 1.O MPA
Electrical Power Requirements 100-120 VAC	100-120 VAC (50-60Hz)	100-120 VAC (50-60Hz)
Required Circuit Amperage - Dedicated Line	20 AMPS	20 AMPS
EPO Circuit Provided - (Located on Machine Front)	Yes	Yes
Plug Requirements Type	Type B/20A/120V	Local Plug Type
Receptacle Requirements Type	Type B/20A/120V	Local Plug Type
Receptacles Total (4)	4-STD/120V	4-120V Local Plug Type
Machine Weight	~ 110 Lbs	~ 50 kgs
Maximum Load Capacity (Bench Requirements)	200 Lbs	90 kgs
Physical Dimensions	W23" X D23" X H28"	W580 mm X D580 mm X H711 mm
Working Space Requirements
FRONT Side of Machine	3'	838.2 mm
LEFT Side of Machine	1'	304.8 mm
RIGHT Side of Machine	1'	304.8 mm
REAR Side of Machine ( Service Access)	1'	304.8 mm
Machine Installation Suggested Location	good lighting and well ventilated	good lighting and well ventilated
Air Inlet Size and Fitting Type (Located in Machine Rear /Single Filter Regulation)	0.25" OD Legris Type	6.35mm OD Legris Type
Air Inlet Tubing Size (Located in Machine Rear /Single Filter Regulation)	*0.236” OD	*6mm OD
Exhaust Requirements Ventilation Flow (25CFM )	0.25" CFM	6.4 mm
Machine Height Adjustment Range (Foot Pads are 1" in Diameter)	1"	25 mm
Serial Number Location	Machine Rear	Machine Rear
Computer System
Control System	Internal Flash Contoller	Internal Flash Contoller
Power Requirements PC Controller	120 VAC	120 VAC
Video Display	15" Flat Panel Display	381 mm Flat Panel
Power Requirements Video Display	120 VAC	120 VAC

*The RD500Series uses a metric based SMC Regulator fitting for connection to factory Air. The Rework station is supplied with 6mm OD (.236”) x 4mm (.157”) black nylon tubing. The supplied 6mmOD Nylon tubing will fit in a .25” compression fitting.

RD-500 Series III Manual (Printable PDF)

The end user can be assured, that DEN-ON Instruments of Japan complies with all requirements and guideline laws on safety and efficacy, in accordance with TUV requirements and all applied standards.

The end user can be assured, that DEN-ON Instruments of Japan complies with all requirements and guideline laws on safety and efficacy, in accordance with CE requirements and all applied standards.

SITE SEARCH

WebMaster

Site Map

DEN-ON™ RD-500SH Series III Rework Stations Technical Specifications

Semi Automated BGA/SMT Rework Stations for Eutectic and Lead Free Solders

DEN-ON RD-500SH Specifications Semi-Automated BGA/SMT Rework Station

DEN-ON™ RD-500SH Series III
Rework Stations
Technical Specifications

DEN-ON RD-500SH Specifications
Semi-Automated BGA/SMT Rework Station